Anodizing   

Aluminum alloys are anodized to increase corrosion resistance and to allow dyeing (coloring), improved lubrication, or improved adhesion.  However, anodizing does not increase the strength of the aluminum object. The anodic layer is non-conductive.
 
When exposed to air at room temperature, or any other gas containing oxygen, pure aluminum self-passivates by forming a surface layer of amorphous aluminum oxide 2 to 3 nm thick, which provides very effective protection against corrosion. Aluminum alloys typically form a thicker oxide layer, 5-15 nm thick, but tend to be more susceptible to corrosion. Aluminum alloy parts are anodized to greatly increase the thickness of this layer for corrosion resistance.
 
Although anodizing produces a very regular and uniform coating, microscopic fissures in the coating can lead to corrosion. Further, the coating is susceptible to chemical dissolution in the presence of high and low pH chemistry, which results in stripping the coating and corrosion of the substrate. To combat this, various techniques have been developed either to reduce the number of fissures or to insert more chemically stable compounds into the oxide, or both. For instance, sulfuric anodized articles are normally sealed, either through hydro-thermal sealing or precipitating sealing, to reduce porosity and interstitial pathways that allow for corrosive ion exchange between the surface and the substrate. Precipitating seals enhance chemical stability but are less effective in eliminating ion exchange pathways. Most recently, new techniques to partially convert the amorphous oxide coating into more stable micro-crystalline compounds have been developed that have shown significant improvement based on shorter bond lengths.

Process

The anodized aluminum layer is grown by passing a direct current through an electrolytic solution, with the aluminum object serving as the anode (the positive electrode). The current releases hydrogen at the cathode (the negative electrode) and oxygen at the surface of the aluminum anode, creating a build-up of aluminum oxide. Alternating current and pulsed current is also possible but rarely used. The voltage required by various solutions may range from 1 to 300 V DC, although most fall in the range of 15 to 21 V. Higher voltages are typically required for thicker coatings formed in sulfuric and organic acid. The anodizing current varies with the area of aluminum being anodized, and typically ranges from 30 to 300 amperes/meter² (2.8 to 28 ampere/ft²).
 
Aluminum anodizing is usually performed in an acid solution which slowly dissolves the aluminum oxide. The acid action is balanced with the oxidation rate to form a coating with nanopores, 10-150 nm in diameter.[6] These pores are what allow the electrolyte solution and current to reach the aluminum substrate and continue growing the coating to greater thickness beyond what is produced by auto-passivation.[8] However, these same pores will later permit air or water to reach the substrate and initiate corrosion if not sealed. They are often filled with colored dyes and/or corrosion inhibitors before sealing. Because the dye is only superficial, the underlying oxide may continue to provide corrosion protection even if minor wear and scratches may break through the dyed layer.
 Conditions such as electrolyte concentration, acidity, solution temperature, and current must be controlled to allow the formation of a consistent oxide layer. Harder, thicker films tend to be produced by more dilute solutions at lower temperatures with higher voltages and currents. The film thickness can range from under 0.5 micrometers for bright decorative work up to 150 micrometers for architectural applications.

Sulfuric Acid Anodizing (Type II and III)

Sulfuric acid is the most widely used solution to produce anodized coating. Coatings of moderate thickness 1.8 μm to 25 μm (0.00007" to 0.001") are known as Type II in North America, as named by MIL-A-8625, while coatings thicker than 25 μm (0.001") are known as Type III, hardcoat, hard anodizing, or engineered anodizing. Very thin coatings similar to those produced by chromic anodizing are known as Type IIB. Thick coatings require more process control, and are produced in a refrigerated tank near the freezing point of water with higher voltages than the thinner coatings. Hard anodizing can be made between 13 and 150 μm (0.0005" to 0.006") thick. Anodizing thickness increases wear resistance, corrosion resistance, ability to retain lubricants and PTFE coatings, and electrical and thermal insulation.

Etch

After sulfuric acid anodizing an etch process is used to provide a uniform matte finish.   The etch can also be used to chemically mill parts and remove minor surface defects.

There are three types of etch baths:
1.       Conventional Etch (No-Dump)
2.       Caustic Recovery Etch
3.       Acid Etch

Conventional Etch
·         High caustic, aluminum.
·         Contains additives to keep the aluminum in solution.
·         Produces a smooth matte finish.
·         Etch times can be long.
 
Caustic Recovery Etch
·         Equipment removes aluminum and keeps caustic.
·         Produces a sellable waste.
·         Bath has low aluminum levels.
·         Sensitive to contaminates.
·         Finish is not as good as conventional etch.
 
Acid Etch
·         Newest technology.
·         Produces a superior smooth matte finish.
·         Can hide many die lines and extrusion defects.
·         Not sensitive to zinc contamination.
·         Reduces sludge in waste treatment.

Able utilizes an Acid Etch process

Templates in Time